1. ZT1P72MN left crankcase sub-components (short wheelbase version)
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: The part assembly contains bearings or oil seals. The specific installation model can be viewed from the maintenance manual in the "My-More Functions-Download Zone" in the ZONTES Mall APP.
|
|
|
|
2. GB16674 M6×75 Hexagon flange bolts (9.8 grade/environmental color Zinc)
|
|
|
|
|
|
|
|
3. φ8×14 hollow locating pin
|
|
|
|
|
|
|
|
4. YM10×1.25-M10×1.25×190 studs bolts
|
|
|
|
|
|
|
|
5. Non-standard M6×25.5 double-head 9.8 studs bolts (environmental color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
3
|
|
Remarks: ① and ② of the old model have been discontinued. If you need to replace the old double-headed studs, you must purchase them in pairs. "1251300-096000 Non-standard cover-shaped 9-grade nut M6×13 (environmentally protection color zinc)"; if it is ①, and it needs to chamfer 1.5~2 on the fine filter cover before assembly.This stud cannot be used in the engine cylinder head of the 200 model.
|
|
|
|
6. Non-standard cover type 9 degree nut M6×13 (environmental color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
3
|
|
Remarks:0# Sleeve. This is a new, taller nut. If you need to replace the stud, you must purchase this taller nut at the same time. This nut can replace the old, shorter nut, and for the sake of uniformity, it is recommended to replace them simultaneously. For water-cooled series models such as KD150-U/G1/Z2, the standard torque is 10N ± 1.5N.m; for series models such as ZT310, ZT350, ZT250-S/R, it is 12N ± 1.5N.m; for ZT310T-M, it is 10N ± 1N.m. Starting from February 19, 2025, the two nuts at the ECU installation location of ZT350-V1/VX/S will be switched to this model, and the original nuts will be phased out. It is recommended to purchase 2 pieces for replacement at the same time.
|
|
|
|
7. ZT1P58MJ main bracket reset spring column
|
|
|
|
|
|
|
|
8. M12×1.5×15 ablassschraube (9.8 grade/environmental color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remark: It is recommended to replace the combination seal 12×φ20×2 at the same time of replacing the oil. ZT310/350 &250-S/R series knight car the standard torque is 24±4N.m;KD/ZT125/150/155-U/U1/G1/Z2/GK is 25±3N.m;ZT125/310/350/368 series scooters 25N.m.
|
|
|
|
9. Combined sealing gasket 12×φ20×2
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: It is recommended to replace with the new parts after disassembly to prevent leakage.
|
|
|
|
10. M14×1.5 filler cap nut
|
|
|
|
|
|
|
|
11. 13.8×2.5 Acrylate rubber o-rings
|
|
|
|
|
|
|
|
12. GB70.1 inner hex bolt M8×16(color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: 6# inner hexgon socket.
|
|
|
|
13. 8.3×15.5×1 copper gasket
|
|
|
|
|
|
|
|
14. Non-standard bolt M8×25 (color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: Standard torque when used for the gearbox oil drain port of the scooter series: 20 N.m. Torque when used for the rear disc brake caliper: 30 N.m. 14# socket.
|
|
|
|
15. φ12.4×φ19×35.3 upper hanging bushing
|
|
|
|
|
|
|
|
16. Φ17.6×φ2.4 nitrile rubber O-ring
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
18. GB894.1 Retaining ring for shaft φ18
|
|
|
|
|
|
|
|