1. ZT180MN right crankcase cover(with oil choking )
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: Only contain oil plug. Please check the clutch lever seat of the left hand to confirm the same status and then place the order. The clutch will be improved from September 10, 2018. The part needs to be unified with the clutch rocker to be used normally.
|
|
|
|
2. ZT180MN Water seal subassembly
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: The ZT180MN water seal sub-assembly includes a water seal static ring and a water seal dynamic ring; the water seal dynamic ring is installed on the pump impeller, and the water seal static ring needs to be press-fitted on the right crankcase cover; please ensure that you have the ability to install it before proceeding. Place an order.
|
|
|
|
3. 6201-C deep groove ball bearing(FAG)
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: The picture shows the installation position of the bearing on the right crankcase cover of the 310 vehicle engine.Confirm your ability to assemble independently before placing an order
|
|
|
|
4. FB12×18×5 fluorine rubber seal
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: Confirm you have ability to assemble and place orders
|
|
|
|
5. NY12×23×7 Hydrogenated nitrile rubber oil seal
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: Click on the enlarged picture to confirm the specifications before purchasing, and then purchase it by yourself.
|
|
|
|
6. FB12×24×5 HNBR oil seal
|
|
|
|
|
|
|
Quantity
|
|
|
3
|
|
Remarks: Click on the enlarged picture to confirm the specifications before purchasing, and then purchase it yourself.Confirm your ability to assemble independently before placing an order
|
|
|
|
7. FB14×22×5 Hydrogenated nitrile oil seal.
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks:Be sure to confirm that you have ability to assemble it and then you place an order.
|
|
|
|
8. type hole circlip φ24×1
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks:Be sure to confirm that you have ability to assemble it and then you place an order.
|
|
|
|
9. GB290-HK1210 needle rolling bearing
|
|
|
|
|
|
|
Quantity
|
|
|
3
|
|
Remarks: Confirm you have ability to assemble and place orders
|
|
|
|
10. ZT180MN inlet and outlet water pipe joints
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: The O-ring specification of the water pipe joint is 19×1.5.
|
|
|
|
11. 19×1.5 ethylene propylene terpolymer O shape circle
|
|
|
|
|
|
|
|
12. Non-standard M6×25.5 double-head 9.8 studs bolts (environmental color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
3
|
|
Remarks: ① and ② of the old model have been discontinued. If you need to replace the old double-headed studs, you must purchase them in pairs. "1251300-096000 Non-standard cover-shaped 9-grade nut M6×13 (environmentally protection color zinc)"; if it is ①, and it needs to chamfer 1.5~2 on the fine filter cover before assembly.This stud cannot be used in the engine cylinder head of the 200 model.
|
|
|
|
13. Non-standard cover type 9 degree nut M6×13 (environmental color Zinc)
|
|
|
|
|
|
|
Quantity
|
|
|
3
|
|
Remarks:0# Sleeve. This is a new, taller nut. If you need to replace the stud, you must purchase this taller nut at the same time. This nut can replace the old, shorter nut, and for the sake of uniformity, it is recommended to replace them simultaneously. For water-cooled series models such as KD150-U/G1/Z2, the standard torque is 10N ± 1.5N.m; for series models such as ZT310, ZT350, ZT250-S/R, it is 12N ± 1.5N.m; for ZT310T-M, it is 10N ± 1N.m. Starting from February 19, 2025, the two nuts at the ECU installation location of ZT350-V1/VX/S will be switched to this model, and the original nuts will be phased out. It is recommended to purchase 2 pieces for replacement at the same time.
|
|
|
|
14. ZT180MN water pump (insert thread)
|
|
|
|
|
|
|
|
15. Thrust washer,12.2×20×1
|
|
|
|
|
|
|
|
16. φ5×16 cylindrical pin
|
|
|
|
|
|
|
|
17. ZT180MN Water pump gear
|
|
|
|
|
|
|
|
18. ZT180MN Water pump shaft
|
|
|
|
|
|
|
|
19. 9.2 × 18 × 1 Thrust Washer
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: The production date of the motorcycles is after mid-December 2019 , and you can purchase this piece directly. If the production date is mid-December 2019, you are recommended to measure the original gasket size before purchasing it yourself.
|
|
|
|
|
|
|
|
|
|
|
|
Quantity
|
|
|
1
|
|
Remarks: Please check the left hanglebar clutch rocker arm to confirm the status and then place the orders. From September 10, 2018, the clutch was improved. This part needs to be unified with the clutch rocker arm to be used normally.
|
|
|
|
21. ZT173YMM clutch pull rod spring
|
|
|
|
|
|
|
|
22. ZT180MN oil level gauge
|
|
|
|
|
|
|
|
23. 15×3.1 acrylate adhesive O-ring
|
|
|
|
|
|
|
|